Camaro Zone Forums banner

intake

  1. 4th Gen (1993-97) Camaro and Firebird Tech
    Hello, i have a 97 z28 lt1, and im stuck on making a decision. Cant decide whether to get a cold air intake, looking at an slp, or to get a ported and polished intake. Looking to get the best bang for my buck (under $300). Car is bone stock other than new flowmaster exhaust, auto with 130xxx
  2. 3rd Gen (1982-92) Camaro and Firebird Tech
    ok so im confused on what all changed in 87 i know they changed to center bolt valve covers in 87 but did the bolt holes on the intake change to the vortex style i need to know because my previous motor for my iroc was a 85 and i had a performer intake on it with i prefer over the stock one...
  3. General Camaro & Firebird Tech
    I have my exhaust done already, magnaflow cat back with high-flo cat, sounds really nice but im looking to get it a little deeper as well as a little louder. im mostly focused on HP and RWHP. debating between Cold Air Intake and Short Ram? So far it seems like a CAI is the way to go. just want...
  4. V6 Camaro and Firebird Tech
    I just bought my first car: a 2000 Camaro 3800 Series II v6. Not a rocket, but insurance is expensive for teenagers and I've always wanted a Camaro of my own. I fixed pretty much everything that was wrong with it, and now I am looking for modifications that I can do to it. I was thinking of...
  5. General Camaro & Firebird Tech
    Hello, all. This is my 1st post. Haven't even detailed my profile yet. I'll try to condense this: '96 camaro rs, 3800 series, all stock. in the process of replacing a leaking lower intake manifold gasket. Already got the lower torqued down & had started to torque the upper plenum. When torquing...
  6. 4th Gen (1993-97) Camaro and Firebird Tech
    So whats the best intake you can have for the 3.4? The stock intake doesn't look to bad so i threw in a spectre high flow and that was the end of it. It looks like it just routes to a couple places from inner fender on the driver side and behind the left hand side headlight, which gives it...
  7. 4th Gen (1993-97) Camaro and Firebird Tech
    I've been having an issue with a backfire from the intake when I go over 4000rpm sitting still or on the road with WOT or heavy throttle. no SEL or anyother indications of what is happening. At allother times, runs great low to 75% throttle, idles great, no miss or anything till 4k, then popping...
  8. V6 Camaro and Firebird Tech
    hi i just recently bought a 1998 v6 firebird and im looking to make it faster. ideally fast enough to beat my friends 2006 v6 mustang haha. anyway i was wondering if it was possible that the slp air box lid for a v8 firebird ( SLP Air Lid - LS1 Camaro & Firebird (1998-2002) ) would also be...
  9. V6 Camaro and Firebird Tech
    Fast Toys Performance Parts You think it'd really be a better upgrade than ported TB?
  10. 4th Gen (1998-02) Camaro and Firebird Tech
    Has any one tried the air intake modification off of the Install University? It is the cheap mans Cold Air Box. I just did mine but have not taken it out to see if there is a difference. I figure if it doesn't work to my liking I will have an excuse to get a Cold Air Box system. :drool:
  11. 4th Gen (1998-02) Camaro and Firebird Tech
    Hello there, I got a 98 firebird v6 3.8 and I'm looking to put in an air intake for it. I was wondering what air intakes are out there that will fit my engine size. Thanks:icon_wink:
  12. 4th Gen (1998-02) Camaro and Firebird Tech
    Sent my FAST 90mm off to get a nice port job done. Tony Mamo at AFR does this by hand. Had to clean it up really good for him to work on it, but it should be worth it. Turnaround time was outstanding. And he was great working with me on a lost check (that UPS eventually found). Before...
Top